7004t-lm-v3 Password Reset ((link)) May 2026

7004T-LM-V3 Password Reset Guide: Recover Access to Your DVR Locked out of your 7004T-LM-V3

DVR? This motherboard model is frequently found in unbranded or white-label H.264 network video recorders. Because these devices lack a centralized support brand, resetting the password requires specific manual or technical steps. Below are the most effective methods to perform a 7004T-LM-V3 password reset and regain control of your security system. Method 1: Hardware Jumper Reset (Most Reliable)

If your device has the LY8008R-5MN motherboard (common for this model), there is a physical way to clear credentials using the onboard pins.

Preparation: Power off the DVR and disconnect all cables, including the power supply and HDMI.

Open the Casing: Use a Phillips screwdriver to remove the cover. Locate the motherboard.

Identify the JPW Pins: Look for a set of three pins labeled JPW near the SATA connectors. Pin 1: GND (Ground) Pin 2: RESET Pin 3: VCC

Short the Pins: Use tweezers or a paperclip to bridge Pin 1 and Pin 2.

Power On: While holding the bridge, plug in the power. Wait for a single long beep (usually 5–7 seconds) before removing the tool.

Login: Once the system reboots, use the default credentials: Username: admin Password: admin (or leave blank). Method 2: Software Super Password Generator

Many 7004T-LM-V3 units are "XMEye" based, allowing you to bypass the lock using a temporary password generated from the system date.

Step 1: Note the exact Date and Time displayed on your DVR's login screen (e.g., 2024-05-04). 7004t-lm-v3 password reset

Step 2: Use a "Superadmin" or "DVR Password Generator" tool (available on sites like Unifore) on a PC.

Step 3: Enter the DVR's current date into the generator to receive a one-time code.

Step 4: Enter this code into the DVR's password field. If successful, the system will allow you to create a new admin password immediately. Method 3: CMOS Battery Removal

If the hardware jumper method isn't working, a "hard drain" might reset the system clock to a factory default date, which sometimes clears the user database or allows the use of known default passwords.

Open the DVR and locate the silver coin-cell battery (CR2032).

Remove the battery for at least 30 seconds to 2 minutes while the unit is unplugged. Reinsert the battery and power on.

Try default logins such as admin/admin, admin/123456, or leaving the password field blank. Troubleshooting Persistent Login Errors

If the reset succeeds but you still can't log in, you may have a "stale session" error.

The 90-Second Rule: After performing a hardware reset, unplug the power and wait 90 seconds to fully discharge the capacitors.

Boot without Peripherals: Reconnect only the power and let the system boot for 2 full minutes before plugging in the monitor or mouse. 7004T-LM-V3 Password Reset Guide: Recover Access to Your

Please provide the brand name (e.g., Casper, ZOSI, or XVR) printed on the front of your device for tailored instructions.

Resetting the password for a 7004T-LM-V3 (typically an AHB 4-channel H.264 DVR board) requires physical access to the device's motherboard to clear the system's flash memory. Standard soft-reset methods like removing the backup battery are often ineffective because credentials are stored in non-volatile memory. Standard Hardware Reset Method

For models with the V3 firmware, the most reliable recovery involves "shorting" specific pins on the internal motherboard:

Power Off: Disconnect all power and peripheral cables (HDMI, USB, etc.).

Open the Case: Use a screwdriver to remove the DVR's outer shell and locate the motherboard.

Locate the Jumper: Look for a set of three pins labeled JPW or similar (Reset Jumper) near the SATA connectors.

Bridge Pins 1 and 2: Use a small metal tool, such as a paperclip or tweezers, to touch both Pin 1 (GND) and Pin 2 (RESET) at the same time.

Power On: While holding the short, reconnect the power cable. Continue holding until you hear a single beep (usually after 5–7 seconds).

Reboot: Remove the shorting tool immediately after the beep and wait at least 30 seconds for the system to initialize. Alternative Recovery Options

If the physical jumper is not visible or accessible, you may try these secondary methods: Troubleshooting & cautions

Default Credentials: Try logging in with the factory defaults. The username is typically admin, and the password is often blank (empty) or 123456.

Super Password Generators: Some generic H.264 DVRs using High Silicon chips can be unlocked using "Super Passwords" generated from the device's system date or serial number.

Technical Support: Contact the original vendor or manufacturer (such as Xiongmai Tech) for a temporary override code based on the device's on-screen serial number.

Disclaimer: This guide is intended for authorized administrators recovering access to devices they own or manage. Resetting a device to factory defaults will erase all existing configurations (IP settings, channel configurations, user accounts). Ensure you have physical access to the device and a backup of your configuration if possible.

4. Reset the router

rommon 2 > reset

Troubleshooting & cautions

Generic password reset steps for unknown 7004t-lm-v3

⚠️ Warning: Resetting will erase custom settings (WiFi names, IP configurations, user accounts).

How to Connect:

  1. Physical connection: Plug your PC into any LAN port (Ports 1–4). Do not use the WAN port for initial access.
  2. Set your PC’s IP: Manually assign 192.168.1.10 (subnet 255.255.255.0, gateway 192.168.1.1) or simply enable DHCP on your PC—the router will assign an IP automatically.
  3. Open a browser (Chrome/Firefox/Edge). Clear your cache.
  4. Navigate to: http://192.168.1.1
  5. At the login prompt, enter admin / admin.

Success! You should now see the dashboard.

Method 2: Hardware Jumper / DIP Switch Reset

Some 7004t-lm-v3 revisions include a physical password bypass jumper (JP1 or SW2). This is useful if the U-Boot interrupt is disabled.

  1. Power off the unit.
  2. Locate the 2-pin jumper labeled PWD_BYPASS or FACTORY.
  3. Short the jumper with a shunt.
  4. Power on. The device will bypass authentication.
  5. Log in as root (no password).
  6. Run passwd to set a new password.
  7. Power off, remove the jumper, and restart normally.

Note: Not all SKUs of the 7004t-lm-v3 include this jumper. Check your hardware revision manual.

Step-by-Step: Soft Reset to Default Credentials

Default credentials after a soft reset:

Procedure:

  1. Power on the 7004t-lm-v3.
  2. Watch the SYS LED (System LED). It will blink rapidly during boot.
  3. Locate the Reset button (usually a recessed pinhole on the front or back panel).
  4. Timing is critical: Wait exactly 10–15 seconds after power-on (when the SYS LED changes from fast blink to a slow, rhythmic blink).
  5. Press and hold the Reset button for 5 seconds (no more, no less).
  6. Release. The SYS LED should flash three times quickly.
  7. The device will reboot automatically (or wait 30 seconds and power cycle manually).

Result: The password is now reset to factory default (admin/admin), but your network configuration, static routes, and VPN settings remain intact.

Troubleshooting: If the soft reset fails, you held the button too long (triggered a hard reset) or not long enough. Try again. If after three attempts you still cannot log in, proceed to the hard reset.

6. Load the saved config (optional but recommended)

Router# copy startup-config running-config
You've just added this product to the cart:
CONTACT US