How to Install/Flash Firmware on Allwinner A133 Devices (PhoenixSuit Method)
This post provides a step-by-step guide to installing or flashing stock firmware on an Allwinner A133 device using PhoenixSuit, the standard flashing tool for Allwinner SoCs.
⚠️ Disclaimer: Flashing firmware can damage your device if done incorrectly. Ensure you have the exact firmware for your specific board ID. You are responsible for your own device. 🛠️ Prerequisites PC: Windows PC (Windows 10/11 recommended). USB Cable: A high-quality USB data cable. Battery: At least 80% charge or plugged into power.
Firmware File: .img firmware file specifically for your A133 device. Tools: PhoenixSuit V1.10 Allwinner USB Drivers (ensure they are installed properly). 1. Locate the Correct Firmware
Unlike mainstream phones, Allwinner devices (especially generic tablets) require the exact firmware matching the motherboard identification.
Method: You may need to physically open your device to find the Board ID (e.g., EM_A133_V1.x).
Search for your firmware using this ID, not the model name on the case. 2. Prepare the PC and Drivers Download and Install: Install PhoenixSuit.
Drivers: Open Device Manager on Windows, connect the device in flash mode, and install the USB drivers if they are not recognized automatically. 3. Flashing Process (Using PhoenixSuit) Open PhoenixSuit: Launch the application.
Load Firmware: Click the Firmware button in the top menu and select your .img file. allwinner a133 firmware install
Power Off Device: Ensure the A133 device is fully turned off. Enter FEL Mode (Flash Mode):
Hold down the Volume Down (or sometimes Volume Up/Menu) button. While holding the button, connect the USB cable to the PC.
Press the power button 3-5 times quickly, or keep holding the volume button until the PC makes a sound.
Verify Connection: PhoenixSuit should pop up a dialogue box asking to Upgrade or Force Upgrade. Flash: Click "Yes" to start the firmware update process.
Wait: Do not disconnect the cable. The process will show a progress percentage.
Finished: Once a "Firmware Update Succeeds" message appears, the device will reboot automatically. ⚡ Troubleshooting
Device not recognized: Try a different USB port (rear USB ports on desktops are better) or a different cable.
Flash Fails/Stuck: Ensure you are using the correct firmware. Sometimes, changing "Upgrade" to "Force Upgrade" in PhoenixSuit fixes issues. How to Install/Flash Firmware on Allwinner A133 Devices
Boot Loop/Black Screen: This usually means the firmware is wrong for your specific board revision.
If you can provide the board ID (usually printed on the circuit board, like "A133_XXX") or the brand name of your tablet, I can try to help you locate the correct firmware.
Technical Report: Allwinner A133 Firmware Installation Guide Allwinner A133 Go to product viewer dialog for this item.
is a quad-core 64-bit ARM Cortex-A53 processor commonly found in budget-friendly Android tablets. Because many generic tablets use this chip, identifying the exact firmware for your specific device model is the most critical step in a successful installation. 1. Pre-Installation: Identifying Your Hardware
Before downloading any files, you must verify the specific Board ID of your device. Generic tablets often share the same processor (A133) but use different internal circuit boards.
Physical Inspection: Open the device (typically by prying the back cover with a plastic tool) to find the Board ID printed directly on the PCB (e.g., "CB-MRU" or similar alphanumeric codes).
Software Identification: If the device still boots, check Settings > About Tablet for the specific build number and model name. 2. Required Tools and Software
Allwinner provides official utilities to facilitate firmware flashing from a PC to the device's storage (eMMC). Allwinner A133 | PDF | Graphics Processing Unit - Scribd Disconnect the USB cable
Q: Can I install a generic Android ROM (like LineageOS) on an A133 tablet? A: Unlikely. Allwinner does not publicize its GPU drivers (Mali-G31) and hardware abstraction layer (HAL) sources. Without custom device tree files, a generic ROM will not boot.
Q: My device has a "Secure Boot" lock. Can I still flash? A: Some commercial A133 devices have a locked bootloader that only accepts signed firmware from the manufacturer. If you get a "Signature check fail" error, you cannot flash unofficial firmware.
Q: The firmware flash finished, but now the touch screen is inverted or not working. A: You flashed firmware from a similar but not identical device. The touch panel driver (Goodix, FocalTech) is wrong. Find the exact firmware for your hardware revision.
Q: PhoenixSuit asks for a "Password" to flash. A: Some manufacturers (especially for medical or automotive devices) password-protect the flash process. The password is rarely available to end users. Contact technical support.
C:\firmware\a133_firmware.img).REC or UPGRADE.Finding the correct firmware is the hardest part.
Settings > About Tablet. You will often see codes like A133-Q8, A133-FW, or specific brand model numbers..img. Do not try to flash .zip or .rar files directly; extract them first.PhoenixSuit is the standard tool for Allwinner A133. Here is the exact procedure.
If you flashed a modded firmware, factory OTA updates may overwrite it. Disable com.qualcomm.ota or UpdateCenter via ADB or a package disabler.