Hi Sharp Dvr Reset Password Fix May 2026

To reset the password on a Hi Sharp DVR , you can typically use the official "Dynamic Password" method, which involves generating a temporary code based on the device's current system date and serial number. 1. The Dynamic Password Method (Most Common)

Hi Sharp systems often use a time-sensitive "Super Password" for recovery. Access the Login Screen: On your DVR monitor, right-click and select Locate the Forgot Password Button: "Forgot Password" "Retrieve Password" button on the login prompt. Identify the Device Info: A window will pop up showing the Serial Number System Date/Time currently set on the DVR. Generate the Super Password: Hi Sharp Support or use a "Super Password" generator tool (like GenSuperPassword.exe ) if provided by your vendor. You must provide the

date shown on the DVR screen (e.g., 2026-04-16), as the code changes daily. Enter the Code:

Type the generated code into the password field. If successful, the account will initialize, and you can set a new password. www.mvteamcctv.com 2. Default Credentials

If you have recently factory reset the device or it is brand new, try the standard factory defaults: (case sensitive) , or leave it www.hisharp.com 3. Hardware Factory Reset

If software methods fail, you can manually reset the hardware to clear all settings, including the password. Locate the Reset Button:

Power off the DVR and look for a small button on the back panel. If it's not visible, you may need to unscrew the outer casing to find a button on the PCB (motherboard) labeled Perform the Reset: Press and hold the reset button. While holding, power on the DVR. Keep holding for 10–15 seconds until you hear a beep or see the system reboot.

The DVR will return to factory settings, allowing you to log in with the default credentials. Techage.com 4. Remote Reset via Browser If the DVR is connected to your network: Find the DVR's IP address using the Hi Sharp IP Finder tool Enter the IP into a web browser on your PC. On the login page, click Forgot Password

. Depending on your firmware, it may allow you to reset via a pre-configured security email or by scanning a QR code with a mobile app. www.hisharp.com contact link for Hi Sharp technical support? FAQ - Support | HI SHARP INTELLIGENCE

To reset the password on a Hi Sharp DVR, you should first attempt the manufacturer's official recovery protocol before resorting to hardware-based factory resets.  1. Official Recovery via Dynamic Code 

Hi Sharp's primary method for lost passwords involves generating a temporary code that must be verified by their support team or a distributor. 

Step 1: On the login screen of your DVR, click on "Forget Password".

Step 2: Navigate to the "Retrieve Password" section and select the "Dynamic Code" page.

Step 3: Take a clear photo or screenshot of this dynamic code.

Step 4: Send this image, along with your device's Model Number and Serial Number, to your regional distributor or directly to Hi Sharp support at sales@hisharp.com.tw.

Step 5: Once you receive the temporary verification code, enter it on your DVR to unlock the system and set a new permanent password.  2. Standard Default Credentials 

If you are setting up the device for the first time or if it has already been factory reset, try the default login credentials:  Default Username: admin Default Password: 123456  3. Hardware Factory Reset 

If the software recovery method is unavailable, a physical reset can restore the device to its original factory state, which clears the custom password. 

Pinhole Reset: Look for a small hole labeled "Reset" on the back of the DVR. Insert a paperclip and hold for 10–30 seconds while the device is powered on until you hear a beep.

Internal Motherboard Reset: If no external button exists, you may need to open the casing. Some models have two pads/holes on the PCB that must be shorted with a screwdriver, or a physical button on the motherboard that you hold for 10 seconds during power-up.

CMOS Battery Removal: For older models, removing the small silver coin battery (CMOS battery) for several minutes can sometimes reset the internal clock and system settings, potentially clearing a password.  4. Technical Tools 

For network-based discovery and basic management, Hi Sharp provides the IP Finder Software which can help identify the device's IP and serial number required for the support-based reset.  FAQ - Support | HI SHARP INTELLIGENCE

Forgetting the password to your HI SHARP DVR can be a major roadblock to accessing critical security footage. Fortunately, there are several official and hardware-based methods to regain access. 1. Try Common Default Passwords

Before attempting a hard reset, verify if your system is still using factory settings. The default credentials vary by model:

Admin / 123456: This is the most frequent default for modern HI SHARP DVRs and NVRs. Admin / 1234: Common on older analogue HD units. Admin / 0000: Used on specific 16-channel DVR models.

Admin / Admin: Occasionally used for IP finder software logins. 2. Official "Dynamic Code" Reset

If you cannot log in, HI SHARP provides a "Dynamic Code" recovery method through their authorized channels:

On the DVR login screen, click "Forget Password" or "Retrieve Password".

Navigate to the "Dynamic Code" page, which will display a unique code or QR code. Take a photo or screenshot of this screen.

Contact your regional distributor or the seller you purchased the device from. You can also email sales@hisharp.com.tw with your region, model number, and serial number to receive a temporary unlock code.

3. Password Reset via Mobile App (Hi Sharp EX / Superlive Plus) For newer models with cloud features enabled: Resetting Password of DVR/NVR by Scanning QR Code

To reset a Hi Sharp DVR password, you must use the manufacturer's dynamic code system or a physical factory reset method. Because security systems are designed to prevent unauthorized access, there is no single "universal" button for every model. Primary Reset Methods 1. Official Dynamic Code Method hi sharp dvr reset password fix

This is the recommended process according to the Hi Sharp Intelligence FAQ: Open the login screen on your DVR. Click Forget Password and then Retrieve Password.

Select the Dynamic Code page to generate a unique code or QR code on the screen.

Screenshot this page and send it to your regional distributor or seller.

Alternatively, email the screenshot along with your model number and serial number to sales@hisharp.com.tw. They will provide a temporary recovery code. 2. Physical Hardware Reset

If you cannot contact support, you may be able to force a factory reset using the motherboard: Power off the DVR and open the outer casing.

Locate the Jumper/Button: Look for two metal pins labeled G1 or a small push-button on the motherboard.

Bridge the Pins: Use a conductive tool (like a flathead screwdriver) to hold the two pins together.

Power On: While keeping the pins bridged, plug in the power and wait about 60 seconds.

Release: Once the system beeps or shows a startup screen, the password should revert to the factory default. 💡 Key Credentials & Tools

Factory Default Passwords: Try common defaults like 123456, 000000, or admin (leave password blank).

Third-Party Apps: For older models based on RaySharp or HiSilicon chips, you can try the CCTV Super Password app on Google Play to generate a code based on your DVR's serial number.

CMOS Battery Trick: Removing the small round battery from the motherboard for 5 minutes will often reset the system clock to 2000-01-01, which allows you to use specific "date-based" master passwords provided by technical forums.

If you can tell me the model number (usually on a sticker underneath) or the current system date shown on the screen, I can help you find a more specific master code. AI responses may include mistakes. Learn more

To reset a Hi Sharp DVR password, the standard procedure involves using a "Dynamic Code" provided by the manufacturer or their distributors. 1. Use the Dynamic Code Method

This is the official self-service method for most modern Hi Sharp models.

On the DVR login screen, click "Forget Password" or "Retrieve Password".

Navigate to the "Dynamic Code" page on the device's interface.

Take a photo or screenshot of the QR code or dynamic code displayed on this screen.

Send this photo along with your device's model and serial number to your regional distributor or the seller you purchased from.

Alternatively, you can contact Hi Sharp support directly at sales@hisharp.com.tw to request a temporary reset code. 2. Check Default Credentials

If the device has never been configured or has been recently reset, try the factory default credentials: Username: admin Password: 123456 3. Hardware Factory Reset

If software-based recovery is not possible, you may need to perform a hardware reset to restore the device to its original factory settings.

Physical Reset Button: Look for a small button on the back of the DVR or inside on the motherboard (PCB). Press and hold it for 10–30 seconds while the device is powered on.

Jumper Pins: On some models, you can reset the password by "shorting" specific pins (often labeled G1 or having two adjacent holes) on the motherboard for about 60 seconds while powering on the device.

Note: A factory reset typically only affects settings and does not delete your existing video recordings, though this can vary by model. How to Reset DVR Password

If you are locked out of your Hi Sharp DVR, you can regain access by using the built-in "Dynamic Code" feature or by trying common manufacturer default credentials. 🛠️ Official Reset Method (Dynamic Code)

The most reliable way to reset a modern Hi Sharp DVR is through their official support channel using a temporary code generated by the device itself.

Generate the Code: On the login screen, click "Forget Password", then navigate to "Retrieve Password". Select the "Dynamic Code" page.

Capture the Screen: Take a clear photo or screenshot of the Dynamic Code displayed on your monitor.

Contact Support: Send this image, along with your device's Model Number and Serial Number, to sales@hisharp.com.tw or contact your regional distributor.

Enter Temporary Password: They will provide a unique code that allows you to log in and set a new permanent password. 🔑 Try Default Credentials To reset the password on a Hi Sharp

If your DVR has never been configured or was recently factory reset, it may still use its default login: Username: admin Password: admin or 123456 🔌 Hardware & Alternative Fixes

If you cannot use the software method, you may need to perform a physical reset.

Physical Reset Button: Check the back panel or inside the unit on the motherboard for a small button labeled "Reset." Press and hold it for 10–30 seconds while the device is powered on.

Remove CMOS Battery: Power off and unplug the DVR. Open the case and remove the coin-sized CMOS battery for about 5–10 minutes to clear stored settings.

Mobile Apps: Hi Sharp devices often work with the Superlive Plus or Hi Sharp EX apps (available on Google Play and iOS), which may offer password recovery options if your email was previously linked.

For a general overview of how to perform a hardware reset on various DVR systems, you can watch this guide: How to Reset DVR Password Sortmytask YouTube• 11 Jan 2021 To help you find the exact steps, could you let me know: What is the exact model number (e.g., HS-HK or KD series)? Does your login screen show a QR code or a serial number? Do you have access to the internal motherboard, or FAQ - Support | HI SHARP INTELLIGENCE

If you configured your system through the Hi Sharp Wizard Setup, you might be able to reset via pre-set security questions.

Select "Retrieve Password" and answer the security questions you established during the initial setup.

You can also use the Hi Sharp IP Tool on a PC to search for your device on the network, which may provide model and serial details needed for technical support. Important Support Links Hi Sharp Official FAQ Support Hi Sharp Software & Manual Downloads Hi Sharp Quick Guide (PDF) FAQ - Support | HI SHARP INTELLIGENCE

The process for resetting a Hi Sharp DVR password involves official software tools, dynamic recovery codes, or contacting technical support, as most modern units do not support physical hardware reset buttons. Key Reset Methods for Hi Sharp DVRs Dynamic Code Recovery

The most common official method is through the "Retrieve Password" interface on the local monitor. Navigate to the Forgot Password Retrieve Password section on the login screen. Select the Dynamic Code page. This will display a unique temporary code or QR code.

Take a screenshot or write down the code and send it to your regional distributor or sales@hisharp.com.tw

along with your model and serial number to receive a temporary reset password. Default Credentials Troubleshooting – Why Won’t the Hi Sharp DVR

If you are accessing the system for the first time or after a successful reset, the default login is typically: Hi Sharp IP Finder Software Users can download the IP finder software from the official HI SHARP Support

page. While primarily for locating cameras, it is often the first step in identifying the necessary device information for a support-led reset. "Super Password" Tools (Legacy Models)

For older non-branded or generic H.264 DVRs that share hardware with Hi Sharp, "Super Password" generators (like Superadmin.exe

) may work by generating a 24-hour temporary code based on the current date displayed on the DVR monitor. Summary Review Effectiveness Ease of Use Official Support High (Primary method) Moderate (Requires email/contact) Default Password High (For new/reset units) Software Tools : For security, Hi Sharp recommends setting up Security Questions Pattern Lock

during the initial setup wizard to avoid needing a full reset in the future. Do you need help finding the specific email address

for your regional Hi Sharp distributor to send your dynamic code? FAQ - Support | HI SHARP INTELLIGENCE

For resetting the password on a Hi Sharp DVR , the process varies depending on the age of your device and the firmware version. Most modern Hi Sharp recorders use a Dynamic Code or technical support verification method, while older units may still respond to default credentials. Method 1: The "Dynamic Code" Method (Recommended)

This is the standard procedure for current Hi Sharp DVRs/NVRs.

Open the Login Window: Go to the login screen on your DVR monitor.

Access Password Recovery: Click on "Forget Password" or "Retrieve Password".

Generate Dynamic Code: Select the "Dynamic Code" option. This will display a unique temporary code or a QR code on the screen.

Contact Support: Take a clear photo of this screen and email it to sales@hisharp.com.tw or contact your regional distributor. Include your model number and serial number in the request.

Apply the Key: Once they reply with a temporary password, enter it into the DVR to unlock the system and immediately set a new permanent password. Method 2: Remote Control "Secret" Reset (Specific Models)

Some Hi Sharp NVR and DVR models (like the NF series) allow a reset via the physical remote control: Point the remote at the DVR.

Press the following sequence: 8 → 8 → [ID Number] → Enter.

Note: The ID number is typically between 0 and 65535; if you haven't changed it, try the default ID found in your manual. Method 3: Default Credentials (Old or Unconfigured Units)

If the DVR is new or has been factory reset, try these common default combinations: Username: admin | Password: admin Username: admin | Password: 123456 Username: admin | Password: (Leave Blank)

For a general overview of how DVR password recovery systems typically work across various brands, you can watch this guide: How to Recover DVR Password | 2 Tested Method 2025 Technical Th1nker YouTube• Nov 11, 2023 Prevention Tip

Once you regain access, it is highly recommended to reserve an email address within the Configuration > User settings. This allows you to reset your password via a verification code sent to your phone or email without needing to contact technical support in the future.

Do you have the serial number and model number from the sticker on your DVR, or would you like help finding them? How to Reset DVR Password

Troubleshooting – Why Won’t the Hi Sharp DVR Reset Password Fix Work?

| Symptom | Likely Cause | Solution | |---------|--------------|----------| | Security code changes on every attempt | DVR’s internal battery is dead | Replace CR2032 battery on motherboard, then retry | | Support says “no record of device” | Gray market or cloned DVR | Try Method 4 (hardware reset) | | Reset file not recognized | Wrong firmware version | Re-download correct file for your exact model number | | DVR beeps but no monitor display during reset | Video output changed (VGA vs HDMI) | Try both ports or use BNC output |

Prevention After Reset

• Write down the new password and store it safely.
• Attach a label to the DVR case with credentials.
• Enable security question or email recovery if available.

Warning: Unauthorized reset of a DVR you don’t own may be illegal. Only perform this on your own equipment.

2. Try Default Passwords First

Many Sharp DVRs use common factory defaults:

| Username | Password | |----------------|-----------------| | admin | admin | | admin | 12345 | | admin | (blank) | | admin | 1111 | | 888888 | 888888 |

Also try:

• Username: user / Password: user
• Username: administrator / Password: (blank)

Method A: The Cancel Button Loop

1. On the login screen, click Cancel three times rapidly.
2. This sometimes reveals a hidden "System Info" button in the bottom corner.
3. If that fails, click "Forgot Password" (if visible).
4. A window will appear asking for a "Security Code" or "File Key."

Method 5: Using the RS232 Serial Port for Advanced Users

Professional installers often use a serial console to reset Hi Sharp DVR passwords. This requires a USB-to-TTL converter and terminal software like PuTTY.

1. Connect your computer to the DVR’s RS232 port.
2. Open a serial connection (baud rate usually 115200).
3. Reboot the DVR and watch the boot log.
4. Interrupt the boot process (usually by pressing Ctrl+C or Enter rapidly).
5. Type resetpassword or passwd -d admin in the embedded Linux shell.

This method is not for beginners. One wrong command can brick the DVR.

Method 3: The Official Hi Sharp DVR Reset Password Fix – Using the GUID & Code

This is the most reliable method for bypassing a lost admin password without losing footage. Hi Sharp DVRs generate a unique GUID (Globally Unique Identifier) or Security Code when you request a password reset.

Part 2: The "Low Hanging Fruit" – Default Passwords

Try these immediately. You would be surprised how often these work.

| Username | Password | Success Rate | | :--- | :--- | :--- | | admin | (blank) | 15% | | admin | 12345 | 40% | | admin | 123456 | 10% | | admin | 888888 | 5% | | 888888 | 888888 | 5% | | user | user | 2% |

Fix Attempt #1: Reboot the DVR (unplug power for 30 seconds). Immediately try admin / 12345. Some units reset the login attempt counter after a full power cycle.