Hi Sharp Dvr Reset Password New 〈1080p • 4K〉

To reset the password for a Hi Sharp DVR (New Model), you can typically use the built-in "Dynamic Code" feature or the official password retrieval process. If your device is brand new or recently reset, the default login credentials are usually admin / 123456.

Method 1: Using the "Dynamic Code" (Recommended for New Models)

Newer Hi Sharp models include a self-service recovery option via the local interface. Navigate to the login screen on your DVR monitor. Click on "Forget Password" or "Retrieve Password".

Select the "Dynamic Code" page to generate a unique code or QR code on the screen. Take a screenshot or photo of this dynamic code.

Send the image, along with your model number and serial number, to your regional distributor or directly to Hi Sharp Support at sales@hisharp.com.tw.

They will provide a temporary recovery code to unlock the device and set a new password. Method 2: Initial Setup & Default Credentials

If you are setting up the DVR for the first time or after a successful factory reset, use these default settings: Username: admin Password: 123456

Action: Upon first login, you will likely be prompted by a Wizard Setup to create a strong, unique password. Method 3: Hardware Reset (If Software Fails)

For models where you cannot access the software reset menu, a physical reset on the motherboard may be necessary.

Internal Reset Button: Some units have a small button on the mainboard. Press and hold it for 5–10 seconds while the unit is powered on until you hear a long beep.

Jumper Pins: If there is no button, look for two metal pins labeled "TP" or "J1". Use a screwdriver or tweezers to short-circuit these pins while powering on the device. Hold for roughly 60 seconds to restore factory defaults. FAQ - Support | HI SHARP INTELLIGENCE

If you are locked out of your Hi Sharp DVR or security system, the reset process depends on your specific model and the software version it’s running. As of April 2026, most new Hi Sharp systems utilize "dynamic codes" or QR-based recovery rather than universal master passwords. 1. Use the "Dynamic Code" Method (Newer Models)

For most modern Hi Sharp units, you can generate a temporary code through their official support channels: hi sharp dvr reset password new

Step 1: Go to the DVR's login screen and click "Forget Password" or "Retrieve Password".

Step 2: Look for a button or tab labeled "Dynamic Code". This will generate a unique code or QR code on your monitor.

Step 3: Take a photo or screenshot of this screen and send it to sales@hisharp.com.tw or your regional distributor. Include your device's model number and serial number.

Step 4: They will provide a temporary password. Once you log in, go to Settings > User to set a permanent new password immediately. 2. Common Default Passwords (Legacy Models)

If your device is older or hasn't been set up yet, try these factory defaults (Username is almost always admin): 12345 or 123456 000000 or 0000 admin Leave the password field blank. 3. Physical Hardware Reset

If software methods fail, you can perform a factory reset via the motherboard:

External Reset: Check the back or bottom for a pinhole labeled "Reset." Press and hold with a paperclip for 10–30 seconds while the device is powered on until you hear a beep.

Internal Jumper (Advanced): Power off the unit and open the case. Look for two metal pins labeled "J1" or "G1" (jumpers). Use a screwdriver or tweezers to bridge (connect) these two pins, then power the device on. Hold the bridge for 30–60 seconds to wipe the admin credentials. Troubleshooting Tips

Resetting Password of DVR/NVR by Scanning QR Code - Hik-Connect

To reset the password on a new Hi Sharp DVR , follow these steps based on the manufacturer's official guidance and standard recovery methods for their latest systems. 1. The "Dynamic Code" Method (Recommended)

Newer Hi Sharp models often require a dynamic verification code for security.

Access Reset Menu: On the login screen, click "Forgot Password" or "Retrieve Password". Generate Code: Navigate to the "Dynamic Code" page. To reset the password for a Hi Sharp

Contact Support: Take a clear screenshot of the dynamic code page. Email this screenshot along with your region, model number, and serial number to sales@hisharp.com.tw or your regional distributor. They will provide a temporary password to unlock the system. 2. Default Credentials

If the DVR is new and has not been configured yet, try the factory default login: Username: admin Password: 123456

Alternate: On some older or specific series, the default may be Admin / Admin. 3. Password Reset via Security Questions

If you set up security questions during the initial configuration (common in newer firmware): Click "Retrieve Password" on the login screen.

Answer the security questions you previously configured to bypass the current password and set a new one. 4. Hardware Reset (Last Resort)

If software methods fail, you may need to perform a hardware factory reset, which will wipe all settings.

Locate Reset Button: Open the DVR casing and look for a small button on the motherboard (PCB).

The Process: With the device powered on, press and hold the button for 10–30 seconds until you hear a beep.

Battery Method: Some technicians suggest removing the internal CMOS battery for a few minutes while the device is powered off to clear volatile memory, though this is less consistent on newer digital models.

Pro-Tip: Once you regain access, immediately go to the System Wizard or User Management to set a strong new password and record your Security Questions to avoid future lockouts. FAQ - Support | HI SHARP INTELLIGENCE

1. Check for a default password

Many Hi Sharp DVRs come with one of these default logins:

Try these first — if they work, you can then change the password in the system settings. Username: admin Password: 12345 or 123456 or blank

The Ghost in the Machine: A Comprehensive Guide to Resetting Hi-Sharp DVR Passwords

In the world of CCTV security, few things are more frustrating than the "Digital Video Recorder" becoming a digital paperweight. You turn on the monitor, expecting to see your property, but instead, you are greeted by a gray login screen demanding a password you set three years ago and haven't typed since.

If you are typing "Hi Sharp DVR reset password" into Google, you are likely in one of two positions: you’ve inherited a system with no documentation, or the system has locked you out due to a firmware glitch.

Hi-Sharp DVRs present a unique challenge because the company often acts as an OEM (Original Equipment Manufacturer). Your DVR might say "Hi-Sharp" on the front, or it might be a generic system running a Hi-Sharp board inside a no-name case. Because of this, there is no single "reset button." The solution depends entirely on the specific generation of your hardware and firmware.

Below is a deep dive into the methods to bypass or reset the lock on a Hi-Sharp DVR, ranked from easiest to most advanced.

3. Use Hi Sharp password reset tool (if available)

Hi Sharp sometimes provides a small Windows program called “Hi Sharp Password Reset” or “Super Password Generator”.

Important: How to Change the Password After Resetting

Once you successfully log in using a Master or Super Password, do not restart the DVR yet. The Master Password is usually temporary.

  1. Go to the Main Menu.
  2. Navigate to System or Account.
  3. Select User Management or Modify Password.
  4. Enter the Master Password as the "Old Password."
  5. Enter your New Password twice.
  6. Click Save/Apply.

Phase 2: The Super Password Generator (The "Hash" Method)

If the defaults failed, you are likely looking at a screen that says "Login Failed" or shows a "Hash Code." This is the most common modern security feature for Hi-Sharp units.

When you enter the wrong password multiple times, the DVR will lock you out. On many Hi-Sharp interfaces, a string of characters (numbers or letters) will appear on the screen, often labeled as a Serial Number, MAC Address, or Hash Code.

This code is the key. It is a mathematical representation of the current time or the unit's hardware ID. Because the algorithm is known, developers have created "Password Calculators" that take this code and spit out a temporary master password.

How to use this method:

  1. Identify the Code: Look at the login screen. Write down the Serial Number or the Hash Code exactly as it appears.
  2. Download a DVR Password Calculator: Search for "Hi-Sharp DVR Password Calculator" or "Generic DVR Password Generator." Many of these units utilize the same chips as Hikvision or Dahua generic clones. A popular tool is the "CCTV Super Password" app available on Android phones, or various "Master Password" tools found on CCTV forums.
  3. Input the Code: Enter the Hash/Serial number into the generator.
  4. The Result: The generator will give you a temporary password (often a string of 8 numbers or letters).
  5. Login: Enter admin as the username and the generated code as the password.
  6. Change It: Once inside, immediately go to System Settings > Users and change the password to something you will remember.

Note regarding the Date: Some older Hi-Sharp algorithms rely on the system date. If the DVR has a dead CMOS battery, the date may have reset to 1970-01-01 or 2000-01-01. If your password calculator isn't working, try setting the date in the calculator to match the date shown on the DVR screen (if visible).