Menu
Menu
To locate and use the Mi Pad A0101 (Mi Pad 1) test points for entering EDL mode (9008 port), follow the hardware-level instructions below. This process is typically used to recover bricked devices, bypass accounts, or flash stock firmware when standard methods like Fastboot fail. Mi Pad A0101 Test Point Locations
The test points for the Mi Pad 1 (A0101) are located on the motherboard, requiring you to remove the back cover.
Preparation: Power off the device and carefully pry open the back cover.
Locating the Points: Look near the battery connector or the camera module area.
On the Mi Pad 1, the test points are typically two small golden circular pads located next to each other on the PCB. Note: Ensure you do not confuse them with antenna contacts. Step-by-Step EDL Mode Guide mi a0101 test point new
Disconnect Battery: It is highly recommended to unplug the battery connector from the motherboard to ensure a clean boot into EDL mode.
Short the Points: Use a pair of metal tweezers to bridge (connect) the two identified test points.
Connect to PC: While keeping the points shorted, plug the Mi Pad into your computer using a high-quality USB cable.
Verify Connection: Open Device Manager on your PC. Look under the "Ports (COM & LPT)" section. It should appear as Qualcomm HS-USB QDLoader 9008. To locate and use the Mi Pad A0101
Release Tweezers: Once the PC recognizes the device in 9008 mode, you can stop shorting the points and proceed with tools like the Mi Flash Tool. Troubleshooting
Not Recognized: If it shows as "Unknown Device," ensure you have the Qualcomm QDLoader 9008 Drivers installed.
Mi Account Lock: If you are using this to reset a Mi Account, specialized tools like UnlockTool or Miracle Box are often used after entering EDL mode. BK - Xiaomi Mi A1 EDL Test Point | Facebook Xiaomi Mi Pad 4 Test Point Edl | Tunisia Firmwares Tunisia Firmwares Xiaomi Mi Pad 1 TestPoint | Test Point UnlockTool UnlockTool.Net Xiaomi Mi A1 Test Point - Xiaomi Mi A1 EDL Mode
Xiaomi Mi A1 Test Point | Mi A1 Mi Account Remove File - XDAROM Test Report: MI A0101 – Test Point Validation
| Report ID | MI-A0101-TP-001 | | Date | [Insert date] | | Tester | [Name/ID] | | Unit S/N | [Serial number] | | Test Point Label | TP_A0101 |
| Symptom | Likely Cause | Fix |
|---------|--------------|-----|
| Device not detected in fastboot | Test‑point not properly grounded or shorted. | Re‑check probe connections; use a multimeter for continuity. |
| QDL mode appears but flashing stalls | Inadequate power supply (USB port can’t sustain 500 mA). | Use a powered USB hub or a dedicated 5 V/2 A wall charger with a data cable. |
| “failed to write partition” | Bootloader still locked (test‑point not activated). | Power the phone while the probe is connected; ensure you held Power for at least 3 seconds. |
| Bootloop after flashing custom ROM | Wrong firmware version (e.g., flashing an AOSP build for Snapdragon 615). | Verify you have the A0101‑specific build; check the bootloader version in the ROM’s android-info.txt. |
| Phone won’t turn on after soldering | Acc
DA_SLA_New.bin file.MT6761_Android_scatter.txt from your stock ROM folder.| Parameter | Expected | Measured | Result | |-----------|----------|----------|--------| | DC voltage (TP to GND) | [] V | [] V | PASS/FAIL | | Resistance to GND | [] Ω | [] Ω | PASS/FAIL | | Signal integrity | [spec] | [actual] | PASS/FAIL | | Continuity to target node | YES | YES/NO | PASS/FAIL |
:: 1️⃣ Download the ZIP from the official Qualcomm site
:: 2️⃣ Extract to C:\QDL_Drivers
:: 3️⃣ Run the installer as Administrator
:: 4️⃣ Reboot
Trải nghiệm miễn phí trọn đời
Tạo website, landing page chuyên nghiệp cho các chiến dịch quảng cáo của bạn.
