The Tecom TS1162 is a 3 LED Remote Arming Station (RAS) keypad designed for the Challenger security system. It is frequently used in environments requiring robust construction, such as dusty or wet locations, due to its IP67 rating. 1. Key Specifications
Connectivity: Connects directly to the Challenger RS-485 LAN.
Operating Range: Can be installed up to 1.5 km from the main Challenger panel or Intelligent Access Controller. Inputs/Outputs: One input for Request to Exit (RTE) control.
One open collector output for controlling door relays or strikes.
Durability: Robust molded plastic housing suitable for indoor or outdoor mounting. 2. General Installation Steps While specific detailed
manuals are often restricted to authorized installers, the procedure follows standard Tecom RAS installation protocols as seen in similar models like the TS1001:
Preparation: Power down the Challenger panel before beginning any wiring.
Disassembly: Remove body retaining screws and separate the body from the base. Mounting:
Use the provided template to mark mounting holes and cable entry points.
Ensure the tamper lever will be fully depressed once mounted to avoid false tamper alarms. ts1162 installation manual
Secure the base to the wall using appropriate screws for the surface type.
Addressing: Use the internal DIP switches (typically switches 1–4) to set the unique RAS address on the LAN.
Termination: If this is the last device on the RS-485 LAN, set the LAN termination DIP switch (usually switch 8) to ON. Wiring: Terminate the LAN cabling (+, –, D+, D–). Connect the RTE input and door relay output if required.
Reassembly: Hook the top of the body onto the base tabs and secure with the bottom retaining screws. 3. Support and Documentation
For the full technical manual, installers can access the Aritech/Tecom Support Portal.
Manuals Library: Official documents are hosted on the Aritech Support Site.
Authorized Access: Note that some detailed installation and programming manuals are restricted to trained installers with valid login credentials. Tecom Manuals - Kidde Global Solutions Support
The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) keypad designed for use with Challenger security systems. It features a robust construction suitable for indoor or outdoor use (rated IP67) and includes inputs for request-to-exit (RTE) control and an open collector output for door relays. Installation Steps for Tecom TS1162 Keypad
Based on standard procedures for Tecom RAS units, follow these steps to install the device: The Tecom TS1162 is a 3 LED Remote
Disassemble the Unit: Remove the body retaining screws from the base and pull the body away to disengage the top tabs.
Prepare the Mounting Surface: Use the provided mounting template to locate screw holes and the rear cable entry point. Ensure the surface is flat and vertical to prevent the base from warping.
Mount the Base: Secure the base assembly to the surface using suitable screws or bolts. Ensure the tamper lever will be properly depressed once mounted.
Set Hardware Addresses: Use DIP switches 1 through 4 to set the unique RAS address. If this is the last device on the LAN, set the LAN termination using DIP switch 8. Wiring and Termination:
Power Off: Turn off all power to the Challenger panel before wiring.
Connection: Connect the keypad directly to the Challenger RS-485 LAN (D+ and D- terminals).
Distance: The unit can be located up to 1.5 km from the main panel. Resistors: A
LAN termination resistor is typically required for proper impedance.
Reassemble: Hook the top of the keypad body onto the base tabs, swing the bottom into place, and secure it with the retaining screws. Reference Manuals Temp/RH Probe: At canopy level (plants) or 5
Installation Guide: Detailed technical specifications and diagrams can be found in the Tecom TS1162 Datasheet at Ness Corporation.
System Integration: For broader system configuration, refer to the ChallengerPlus Installation and Quick Programming Manual provided by Aritech.
Do you need the specific DIP switch address table for this keypad or information on programming the door relay? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED * Robust moulded plastic housing. * Indoor or outdoor mounting. * Request to Exit input. aritech.com.au
ChallengerPlus Installation and Quick Programming Manual - Aritech
The Tecom TS1162 is an IP67-rated 3-LED Remote Arming Station designed for secure access control within Challenger systems. Installation requires powering down the panel, mounting the unit, connecting to the RS-485 LAN, and configuring the RAS address. For detailed technical diagrams and specific DIP switch settings, you can refer to the official Tecom TS1162 Datasheet Aritech Support Portal Tecom TS1162 3 LED RAS - Ness Corporation
After completing the TS1162 installation manual steps, run a test:
If all functions work, the installation is successful.