The Xtra Safe KT 82001 (often part of the "Digital Safe" line distributed by brands like Toolworld) is a standard electronic security box designed for home or office use. This manual write-up covers essential operating procedures, from first-time setup to emergency troubleshooting. Quick Setup Guide
Initial Opening: On first use, input the factory default code 1-5-9-B and turn the handle clockwise to open. Programming a New Code: Locate the red button on the inside of the door. Press the button until you hear a beep.
Enter your new code (typically 3–8 digits) and press "B" or "A" (depending on your specific keypad model) to confirm.
Mounting: The safe includes 8mm pre-drilled holes in the bottom and back. It is highly recommended to bolt the safe to a floor or wall to prevent physical removal. Essential Operations
Standard Entry: Enter your programmed code and turn the handle within 5 seconds.
Lockout Mode: If an incorrect code is entered multiple times (usually 3), the safe will enter a timed lockout period ranging from 5 minutes to 1 hour. Battery Maintenance:
Warning: If both red and green lights appear simultaneously, or if the keypad beeps but won't retract the bolts, your batteries are low.
Replacement: The battery compartment is located on the back of the door. Use fresh, name-brand alkaline batteries for consistent voltage. Emergency Override Xtra Safe Kt 82001 Manual
If you forget your code or the batteries die, use the Emergency Override System:
Remove the small cover plate (usually between the keypad and the handle). Insert the override key into the keyhole.
Turn the key counter-clockwise and the handle clockwise simultaneously to open.
Important: Never store the emergency keys inside the safe itself. Troubleshooting Troubleshooting an Electronic Safe lock
First Time Opening: Use the override key provided with the safe. The keyhole is usually located behind a small plastic cover next to the keypad.
Insert Batteries: Open the door and locate the battery compartment on the inside of the door. Insert 4 AA batteries.
Default Code: The factory default code is typically 1-2-3-4 or 1-5-9. Enter the code and press the "A" or "B" key (usually B) to confirm. Turn the handle within 5 seconds to open the door. Programming a New Personal Code The Xtra Safe KT 82001 (often part of
Locate Reset Button: With the safe door open, find the red/reset button on the inside of the door (often near the hinges).
Press Reset: Press the button; you may hear a beep or see a yellow light on the keypad. Enter New Code: Input your new 3-to-8 digit code.
Confirm: Press the "A" or "B" key to save the new code. Test the code while the door is still open to ensure it works before locking it. Security Features (Lockout Mode)
If an incorrect code is entered multiple times, the safe will initiate a security timeout: 1st/2nd Wrong Attempt: 20-second wait before trying again. 3rd Wrong Attempt: The safe may lock for 5 minutes.
Repeated Failures: Continued incorrect entries can result in a 1-hour lockout. Emergency Access If you forget your code or the batteries die: Use the Emergency Override Key. Do not store the override keys inside the safe.
For a digital copy of similar HP Værktøj digital safe manuals, you can check the Toolworld Manual Guide .
Once wired, follow this sequence from the manual to avoid error codes. Part 4: Step-by-Step Operation (How to Power On)
Step 1: Apply Power Turn on the 24V DC supply. The "PWR" LED should illuminate green.
Step 2: Input Verification Close all safety gates and pull out all E-stop buttons. The "In 1" and "In 2" LEDs should turn green.
Step 3: Feedback Loop Ensure the contactor (the machine's main switch) is healthy. The feedback LED should flash once.
Step 4: Reset Press the reset button for 1 second. You will hear an audible "Click" – this is the internal relays energizing. The "Out" LED turns green.
Step 5: Operation Verified The machine is now in "Run" mode.
A (Manual, page 34): “Absolutely not. This device is designed for load securement only, not overhead lifting. Use only properly rated lifting slings.”
For transport on public roads, engage the spring-loaded pawl cover. You should hear a distinct click.
Lost the physical copy? Do not worry. Here are the three most reliable ways to obtain a legitimate manual:
The KT 82001 typically operates on four (4) AA batteries.